Skip to content

BK Resources BKG-GHC-5048-PT 1/2" x 48" Gas Hose Connector in Display Tube

Original price $216.00 - Original price $216.00
Original price
$216.00
$216.00 - $216.00
Current price $216.00

BK Resources builds the BKG-GHC-5048-PT as a 1/2" x 48" gas connector for movable commercial gas appliances: 304 corrugated stainless steel hose, stainless steel radial wrap, a protective translucent coating, and zinc-coated 304 couplings.

This version comes packaged in a point-of-purchase display tube. The hose inside is the same as the BKG-GHC-5048 ($195).

BK designs this hose for mobile gas equipment. It complies with ANSI Z21.69 • CSA 6.16 for connectors for movable gas appliances, and BK's 5-year warranty on it requires a BK Resources restraining cable kit to be used with it.

Quick facts

  • Size: 1/2" inside diameter x 48" long
  • Rated capacity: 110,000 BTU/hr hose only (BK chart, natural gas, 0.5" w.c. drop)
  • Sold as: hose only, in a display tube
  • Certification: cCSAus, Massachusetts approved
  • Hose warranty: 5 years
  • For: movable (caster-mounted) commercial gas appliances, per ANSI Z21.69 • CSA 6.16

How much gas does a 1/2" x 48" hose carry?

From BK's capacity chart, developed using ANSI Z21.69 (natural gas, 0.64 specific gravity, 1,000 BTU per cubic foot, at a 0.5" water column pressure drop). The rating depends on what is installed in line with the hose:

Hose only110,000 BTU/hr
With shut-off valve110,000 BTU/hr
With shut-off valve and quick disconnect76,000 BTU/hr

Your appliance's total input rating should fall under that figure.

Choosing the length

Length is the decision that matters most here. BK offers this 1/2" hose in five lengths: 24", 36", 48", 60" and 72", and its instructions stress picking the length that suits the run from gas line to stub-out.

Measure from the gas outlet to the appliance inlet with the appliance in its working position. The installed hose should have no kinks, twists or excessive bends, and it should not touch the floor. Offsetting the two ends of the hose from each other, as BK recommends, keeps the appliance closer to the wall. A shorter hose carries more gas; a longer one gives the appliance more room to move for cleaning, within the limit set by the restraining cable.

LengthModelPriceCapacity (hose only)
24"BKG-GHC-5024-PT$178163,000 BTU/hr
36"BKG-GHC-5036-PT$195127,000 BTU/hr
48" (this one)BKG-GHC-5048-PT$216110,000 BTU/hr
60"BKG-GHC-5060-PT$262102,000 BTU/hr
72"BKG-GHC-5072-PT$30191,000 BTU/hr

Hose only or a kit?

BK offers this 1/2" x 48" size several ways:

BKG-GHC-5048Hose only: $195 ($21 less than this one)
BKG-GHC-5048-QD-PTHose + quick disconnect (display tube): $255 ($39 more than this one)
BKG-GHC-5048-SCK2Kit #2: hose, quick disconnect, restraining cable: $280 ($64 more than this one)
BKG-GHC-5048-SCK3Kit #3: adds shut-off valve and two 90° elbows: $315 ($99 more than this one)
BKG-GHC-5048-SCK9Kit #9: valve, quick disconnect, cable, two 90° female elbows, two nipples: $324 ($108 more than this one)
BKG-GHC-5048-SW3Swivel Pro kit: Kit #3 contents plus one Swivel Pro: $466 ($250 more than this one)
BKG-GHC-5048-2SW3Swivel Pro kit with two Swivel Pro connections: $615 ($399 more than this one)
BKG-GHC-5048-SP3Set-Pro Kit #3: Kit #3 contents plus two Set-Pro placement guides: $456 ($240 more than this one)
BKG-GHC-5048-SWSP3Set-Pro kit with Swivel Pro: $605 ($389 more than this one)

Parts to go with it

BK requires an approved manual shut-off ball valve at the connection from the gas line to the hose, within 6" of the appliance. The restraining cable is required for the warranty. Matching BK parts:

Installation notes from BK

The key rules from BK's installation manual:

  • Install and leak-test to the National Fuel Gas Code (ANSI Z223.1) and local codes. BK requires qualified personnel for installation and testing.
  • Shut off the main gas line and the ball valve before connecting the hose.
  • An approved manual shut-off ball valve must sit at the connection from the gas line to the hose, within 6" of the appliance. This hose does not include one.
  • The gas outlet may not be hidden in or covered by drywall, flooring or partition walls.
  • Use thread sealant or thread tape on NPT connections and tighten with wrenches.
  • The restraining cable must be attached and stay connected whenever the appliance is in use. Add one: BK's hose warranty requires a BK Resources restraining cable kit.
  • Leak-test the final assembly with a leak-detection solution, never an open flame, and rinse with water afterward to prevent corrosion.
  • Push the appliance back into position and check that the hose isn't over-bent or kinked.

Care: clean connections with mild products and rinse right away, keep the hose away from anything over 230°F (110°C), and never move an installed hose to another appliance. BK's full steps are summarized in our gas hose installation guide, and the BK PDFs are linked below.

Checklist before ordering

  1. Gas load. Add up the input ratings on the appliance data plate and compare with 110,000 BTU/hr, BK's rating for this size hose only. At a 0.2" water column drop, BK's factor of 0.632 gives about 69,520 BTU/hr.
  2. Length. Measure the run with the appliance in place. The table above shows the other lengths and what each carries.
  3. Diameter. If the load is close to the limit, the 3/4" size carries considerably more at the same length.
  4. Hardware. This is hose only. You'll also need a valve, a restraining cable and, if the appliance rolls out, a quick disconnect (see the parts list above).
  5. Gas supply layout. On a dual-fed manifold lineup, BK allows only the ball valve, not a quick disconnect.
  6. Installer. Plan for a qualified gas installer to connect and leak-test it.

BKG-GHC-5048-PT questions

How much gas will the BKG-GHC-5048-PT carry?
BK rates a 1/2" x 48" connector at 110,000 BTU/hr hose only, at a 0.5" water column pressure drop with natural gas (0.64 specific gravity, 1,000 BTU per cubic foot). At 0.2" w.c. that's about 69,520 BTU/hr.

Does it work with propane?
BK's capacity figures are for natural gas. BK's quick connect is approved for 1st, 2nd and 3rd family gases under 50 mbar; for other conditions BK says to contact the manufacturer or gas supplier.

What else do I need?
A 1/2" shut-off ball valve within 6" of the appliance, a 48" restraining cable kit, and usually a 1/2" quick disconnect and 90° elbow. The kit versions of this size bundle them.

Is the restraining cable required?
Yes. BK requires it to stay connected whenever the hose is installed, and its 5-year hose warranty requires a BK Resources restraining cable kit.

What's the warranty?
5 year warranty. The warranty excludes shipping damage, misuse, and installations that don't follow BK's instructions or the applicable gas standards.

Can I move it to another appliance later?
No. BK calls for a new gas hose and installation hardware for each installation.

Specifications

ModelBKG-GHC-5048-PT
TypeGas connector hose
Inside diameter1/2"
Hose length48"
HoseHeavy-duty T-304 corrugated stainless steel, stainless steel radial wrap
CoatingProtective translucent coating
CouplingsT-304 with zinc coating
Rated capacity110,000 BTU/hr hose only
Capacity basisANSI Z21.69 test method; natural gas, 0.64 sp. gr., 1,000 BTU/cu ft, 0.5" w.c. pressure drop
PackagingPoint-of-purchase display tube
CertificationcCSAus; Massachusetts approved
Meets ANSIZ21.69a, Z21.69b, Z21.69-2002, Z21.41a-2005, Z21.41b-2010, Z21.41-2003
Warranty5 year warranty

Documents and downloads

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare