BK Resources BKG-GHC-5072-QD-PT 1/2" x 72" Gas Hose with Quick Disconnect
BK Resources packages the BKG-GHC-5072-QD-PT as a Quick Disconnect Connection Kit: a six-foot, 1/2" I.D. stainless steel hose with radial wrap and protective translucent coating, plus the hardware listed below.
What's in the box
- Gas hose, 72" long x 1/2" I.D. stainless steel hose with radial wrap & protective translucent coating
- (1) quick disconnect
This kit is the hose and quick disconnect only, packaged in a display tube. BK's installation still calls for a shut-off ball valve within 6" of the appliance and a restraining cable that stays connected while the hose is installed. Matching parts: 1/2" ball valve ($27) and restraining cable kit for 72" hose ($32).
Quick facts
- Size: 1/2" inside diameter x 72" long
- Rated capacity: 69,000 BTU/hr with shut-off valve and quick disconnect (BK chart, natural gas, 0.5" w.c. drop)
- Kit includes: hose, quick disconnect
- Certification: cCSAus, Massachusetts approved
- Hose warranty: 5 years; 1 year on the kit hardware
- For: movable (caster-mounted) commercial gas appliances, per ANSI Z21.69 • CSA 6.16
Capacity with the kit installed
Installed with a shut-off valve and quick disconnect in line, BK's capacity chart rates a 1/2" x 72" hose at 69,000 BTU/hr (ANSI Z21.69 test method; natural gas, 0.64 specific gravity, 1,000 BTU per cubic foot, 0.5" water column pressure drop).
For comparison, the same length in 3/4" is rated 168,000 BTU/hr and 1" is rated 339,000 BTU/hr in this configuration.
Your appliance's total input rating should fall under that figure.
Picking a length
Length is the decision that matters most here. BK offers this 1/2" kit in five lengths: 24", 36", 48", 60" and 72", and its instructions stress picking the length that suits the run from gas line to stub-out.
Measure from the gas outlet to the appliance inlet with the appliance in its working position. The installed hose should have no kinks, twists or excessive bends, and it should not touch the floor. Offsetting the two ends of the hose from each other, as BK recommends, keeps the appliance closer to the wall. A shorter hose carries more gas; a longer one gives the appliance more room to move for cleaning, within the limit set by the restraining cable.
| Length | Model | Price | Capacity (valve + quick disconnect) |
|---|---|---|---|
| 24" | BKG-GHC-5024-QD-PT | $228 | 90,000 BTU/hr |
| 36" | BKG-GHC-5036-QD-PT | $243 | 82,000 BTU/hr |
| 48" | BKG-GHC-5048-QD-PT | $255 | 76,000 BTU/hr |
| 60" | BKG-GHC-5060-QD-PT | $298 | 73,000 BTU/hr |
| 72" (this one) | BKG-GHC-5072-QD-PT | $336 | 69,000 BTU/hr |
With 72" of hose, watch for slack. BK's list of common installation mistakes: sharp bends, twists, double bends, and a hose that touches the floor.
Hose only or a kit?
BK offers this 1/2" x 72" size several ways:
| BKG-GHC-5072 | Hose only: $277 ($59 less than this one) |
|---|---|
| BKG-GHC-5072-PT | Hose in display tube: $301 ($35 less than this one) |
| BKG-GHC-5072-SCK2 | Kit #2: hose, quick disconnect, restraining cable: $368 ($32 more than this one) |
| BKG-GHC-5072-SCK3 | Kit #3: adds shut-off valve and two 90° elbows: $403 ($67 more than this one) |
| BKG-GHC-5072-SCK9 | Kit #9: valve, quick disconnect, cable, two 90° female elbows, two nipples: $412 ($76 more than this one) |
| BKG-GHC-5072-SW3 | Swivel Pro kit: Kit #3 contents plus one Swivel Pro: $553 ($217 more than this one) |
| BKG-GHC-5072-2SW3 | Swivel Pro kit with two Swivel Pro connections: $704 ($368 more than this one) |
Before you install
The key rules from BK's installation manual:
- Install and leak-test to the National Fuel Gas Code (ANSI Z223.1) and local codes. BK requires qualified personnel for installation and testing.
- Shut off the main gas line and the ball valve before connecting the hose or quick disconnect.
- An approved manual shut-off ball valve must sit at the connection from the gas line to the hose, within 6" of the appliance. This kit does not include one.
- The gas outlet may not be hidden in or covered by drywall, flooring or partition walls.
- Use thread sealant or thread tape on NPT connections and tighten with wrenches.
- The restraining cable must be attached and stay connected whenever the appliance is in use. Add one: BK's hose warranty requires a BK Resources restraining cable kit.
- Follow the gas-flow arrows on the quick disconnect. Maximum gas pressure through it is 1/2 psi (3.5 kPa), and it's not for dual-fed manifold lineups.
- Leak-test the final assembly with a leak-detection solution, never an open flame, and rinse with water afterward to prevent corrosion.
- Push the appliance back into position and check that the hose isn't over-bent or kinked.
Care: clean connections with mild products and rinse right away, keep the hose away from anything over 230°F (110°C), and never move an installed hose to another appliance. BK's full steps are summarized in our gas hose installation guide, and the BK PDFs are linked below.
Checklist before ordering
- Gas load. Add up the input ratings on the appliance data plate and compare with 69,000 BTU/hr, BK's rating for this size with shut-off valve and quick disconnect. At a 0.2" water column drop, BK's factor of 0.632 gives about 43,608 BTU/hr.
- Length. Measure the run with the appliance in place. The table above shows the other lengths and what each carries.
- Diameter. If the load is close to the limit, the 3/4" size carries considerably more at the same length.
- Hardware. Add a 1/2" shut-off ball valve and a 72" restraining cable kit.
- Gas supply layout. On a dual-fed manifold lineup, BK allows only the ball valve, not a quick disconnect.
- Installer. Plan for a qualified gas installer to connect and leak-test it.
BKG-GHC-5072-QD-PT questions
How much gas will the BKG-GHC-5072-QD-PT carry?
BK rates a 1/2" x 72" connector at 69,000 BTU/hr with shut-off valve and quick disconnect, at a 0.5" water column pressure drop with natural gas (0.64 specific gravity, 1,000 BTU per cubic foot). At 0.2" w.c. that's about 43,608 BTU/hr.
Does it work with propane?
BK's capacity figures are for natural gas. BK's quick connect is approved for 1st, 2nd and 3rd family gases under 50 mbar; for other conditions BK says to contact the manufacturer or gas supplier.
What's in the box?
The 72" x 1/2" hose plus the parts listed above, packaged in a point-of-purchase display tube.
Is the restraining cable required?
Yes. BK requires it to stay connected whenever the hose is installed, and its 5-year hose warranty requires a BK Resources restraining cable kit.
What's the warranty?
5 year warranty on hose, 1 year warranty on quick disconnect. The warranty excludes shipping damage, misuse, and installations that don't follow BK's instructions or the applicable gas standards.
Can I move it to another appliance later?
No. BK calls for a new gas hose and installation hardware for each installation.
How do I clean behind the appliance?
Turn the gas and appliance knobs off, pull back the coupler to release the hose, keep the nipple off the floor, then unhook the cable. To reconnect, reattach the cable first, push the nipple in until it clips, turn the gas on at the ball valve and check for leaks.
Specifications
| Model | BKG-GHC-5072-QD-PT |
|---|---|
| Type | Quick Disconnect Connection Kit |
| Inside diameter | 1/2" |
| Hose length | 72" |
| Hose | Heavy-duty T-304 corrugated stainless steel, stainless steel radial wrap |
| Coating | Protective translucent coating |
| Couplings | T-304 with zinc coating |
| Rated capacity | 69,000 BTU/hr with shut-off valve and quick disconnect |
| Capacity basis | ANSI Z21.69 test method; natural gas, 0.64 sp. gr., 1,000 BTU/cu ft, 0.5" w.c. pressure drop |
| Quick disconnect max pressure | 1/2 psi (3.5 kPa) |
| Packaging | Point-of-purchase display tube |
| Certification | cCSAus; Massachusetts approved |
| Meets ANSI | Z21.69a, Z21.69b, Z21.69-2002, Z21.41a-2005, Z21.41b-2010, Z21.41-2003 |
| Warranty | 5 year warranty on hose, 1 year warranty on quick disconnect |