Skip to content

BK Resources BKG-GHC-10024 1" x 24" Individual Gas Hose Connector

Original price $241.00 - Original price $241.00
Original price
$241.00
$241.00 - $241.00
Current price $241.00

The BKG-GHC-10024 is a two-foot, 1" I.D. gas connector hose from BK Resources, built from 304 corrugated stainless steel with a stainless steel radial wrap and a protective translucent coating. The couplings are 304 with a zinc coating.

It's sold as the hose alone. The same hose in a display tube is the BKG-GHC-10024-PT ($262).

BK designs this hose for mobile gas equipment. It complies with ANSI Z21.69 • CSA 6.16 for connectors for movable gas appliances, and BK's 5-year warranty on it requires a BK Resources restraining cable kit to be used with it.

At a glance

  • Size: 1" inside diameter x 24" long
  • Rated capacity: 872,000 BTU/hr hose only (BK chart, natural gas, 0.5" w.c. drop)
  • Sold as: hose only
  • Certification: cCSAus, Massachusetts approved
  • Hose warranty: 5 years
  • For: movable (caster-mounted) commercial gas appliances, per ANSI Z21.69 • CSA 6.16

How much gas does a 1" x 24" hose carry?

From BK's capacity chart, developed using ANSI Z21.69 (natural gas, 0.64 specific gravity, 1,000 BTU per cubic foot, at a 0.5" water column pressure drop). The rating depends on what is installed in line with the hose:

Hose only872,000 BTU/hr
With shut-off valve813,000 BTU/hr
With shut-off valve and quick disconnect377,000 BTU/hr

Check that number against the input rating on the appliance's data plate.

Choosing the length

BK makes this 1" hose in five lengths: 24", 36", 48", 60" and 72". Because every gas line and stub-out is placed differently, BK says choosing the right length during installation is essential.

Measure from the gas outlet to the appliance inlet with the appliance in its working position. The installed hose should have no kinks, twists or excessive bends, and it should not touch the floor. Offsetting the two ends of the hose from each other, as BK recommends, keeps the appliance closer to the wall. A shorter hose carries more gas; a longer one gives the appliance more room to move for cleaning, within the limit set by the restraining cable.

LengthModelPriceCapacity (hose only)
24" (this one)BKG-GHC-10024$241872,000 BTU/hr
36"BKG-GHC-10036$282744,000 BTU/hr
48"BKG-GHC-10048$307679,000 BTU/hr
60"BKG-GHC-10060$368586,000 BTU/hr
72"BKG-GHC-10072$424541,000 BTU/hr

At 24", this is the shortest length BK makes, so measure carefully before ordering. A hose that has to be pulled straight to reach is too short.

Other 1" x 24" options

BK offers this 1" x 24" size several ways:

BKG-GHC-10024-PTHose in display tube: $262 ($21 more than this one)
BKG-GHC-10024-QD-PTHose + quick disconnect (display tube): $390 ($149 more than this one)
BKG-GHC-10024-SCK2Kit #2: hose, quick disconnect, restraining cable: $412 ($171 more than this one)
BKG-GHC-10024-SCK3Kit #3: adds shut-off valve and two 90° elbows: $485 ($244 more than this one)
BKG-GHC-10024-SCK9Kit #9: valve, quick disconnect, cable, two 90° female elbows, two nipples: $491 ($250 more than this one)
BKG-GHC-10024-SW3Swivel Pro kit: Kit #3 contents plus one Swivel Pro: $730 ($489 more than this one)
BKG-GHC-10024-2SW3Swivel Pro kit with two Swivel Pro connections: $974 ($733 more than this one)

Parts to go with it

BK requires an approved manual shut-off ball valve at the connection from the gas line to the hose, within 6" of the appliance. The restraining cable is required for the warranty. Matching BK parts:

Installation notes from BK

BK's installation manual sets out these requirements for its gas connectors:

  • Install and leak-test to the National Fuel Gas Code (ANSI Z223.1) and local codes. BK requires qualified personnel for installation and testing.
  • Shut off the main gas line and the ball valve before connecting the hose.
  • An approved manual shut-off ball valve must sit at the connection from the gas line to the hose, within 6" of the appliance. This hose does not include one.
  • The gas outlet may not be hidden in or covered by drywall, flooring or partition walls.
  • Use thread sealant or thread tape on NPT connections and tighten with wrenches.
  • The restraining cable must be attached and stay connected whenever the appliance is in use. Add one: BK's hose warranty requires a BK Resources restraining cable kit.
  • Leak-test the final assembly with a leak-detection solution, never an open flame, and rinse with water afterward to prevent corrosion.
  • Push the appliance back into position and check that the hose isn't over-bent or kinked.

Care: clean connections with mild products and rinse right away, keep the hose away from anything over 230°F (110°C), and never move an installed hose to another appliance. BK's full steps are summarized in our gas hose installation guide, and the BK PDFs are linked below.

Before you order

  1. Gas load. Add up the input ratings on the appliance data plate and compare with 872,000 BTU/hr, BK's rating for this size hose only. At a 0.2" water column drop, BK's factor of 0.632 gives about 551,104 BTU/hr.
  2. Length. Measure the run with the appliance in place. The table above shows the other lengths and what each carries.
  3. Diameter. 1" is BK's largest connector; for smaller loads, 3/4" or 1/2" may be enough.
  4. Hardware. This is hose only. You'll also need a valve, a restraining cable and, if the appliance rolls out, a quick disconnect (see the parts list above).
  5. Gas supply layout. On a dual-fed manifold lineup, BK allows only the ball valve, not a quick disconnect.
  6. Installer. Plan for a qualified gas installer to connect and leak-test it.

BKG-GHC-10024 questions

How much gas will the BKG-GHC-10024 carry?
BK rates a 1" x 24" connector at 872,000 BTU/hr hose only, at a 0.5" water column pressure drop with natural gas (0.64 specific gravity, 1,000 BTU per cubic foot). At 0.2" w.c. that's about 551,104 BTU/hr.

Does it work with propane?
BK's capacity figures are for natural gas. BK's quick connect is approved for 1st, 2nd and 3rd family gases under 50 mbar; for other conditions BK says to contact the manufacturer or gas supplier.

What else do I need?
A 1" shut-off ball valve within 6" of the appliance, a 24" restraining cable kit, and usually a 1" quick disconnect and 90° elbow. The kit versions of this size bundle them.

Is the restraining cable required?
Yes. BK requires it to stay connected whenever the hose is installed, and its 5-year hose warranty requires a BK Resources restraining cable kit.

What's the warranty?
5 year warranty. The warranty excludes shipping damage, misuse, and installations that don't follow BK's instructions or the applicable gas standards.

Can I move it to another appliance later?
No. BK calls for a new gas hose and installation hardware for each installation.

Specifications

ModelBKG-GHC-10024
TypeGas connector hose
Inside diameter1"
Hose length24"
HoseHeavy-duty T-304 corrugated stainless steel, stainless steel radial wrap
CoatingProtective translucent coating
CouplingsT-304 with zinc coating
Rated capacity872,000 BTU/hr hose only
Capacity basisANSI Z21.69 test method; natural gas, 0.64 sp. gr., 1,000 BTU/cu ft, 0.5" w.c. pressure drop
CertificationcCSAus; Massachusetts approved
Meets ANSIZ21.69a, Z21.69b, Z21.69-2002, Z21.41a-2005, Z21.41b-2010, Z21.41-2003
Warranty5 year warranty

Documents and downloads

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare