BK Resources BKG-GHC-7524-SCK9 3/4" x 24" Gas Hose Connector Kit #9 with Quick Disconnect, Shut-Off Valve & Elbows
This Connection Kit #9 (BKG-GHC-7524-SCK9) pairs a 3/4" x 24" BK stainless steel gas hose, radial-wrapped with a protective translucent coating, with the fittings to connect it.
What's in the box
- Gas hose, 24" long x 3/4" I.D. stainless steel hose with radial wrap & protective translucent coating
- (1) shut off valve
- (1) quick disconnect
- (1) restraining cable & hardware
- (2) 90° female elbows
- (2) male threaded nipples
Kit #9 swaps the male-to-female elbows of Kit #3 for two 90° female elbows and two male threaded nipples, giving another way to make up the connections at the stub-out and gas supply.
The short version
- Size: 3/4" inside diameter x 24" long
- Rated capacity: 208,000 BTU/hr with shut-off valve and quick disconnect (BK chart, natural gas, 0.5" w.c. drop)
- Kit includes: hose, shut-off valve, quick disconnect, restraining cable
- Certification: cCSAus, Massachusetts approved
- Hose warranty: 5 years; 1 year on the kit hardware
- For: movable (caster-mounted) commercial gas appliances, per ANSI Z21.69 • CSA 6.16
Capacity with the kit installed
Installed with a shut-off valve and quick disconnect in line, BK's capacity chart rates a 3/4" x 24" hose at 208,000 BTU/hr (ANSI Z21.69 test method; natural gas, 0.64 specific gravity, 1,000 BTU per cubic foot, 0.5" water column pressure drop).
For comparison, the same length in 1/2" is rated 90,000 BTU/hr 1" is rated 377,000 BTU/hr in this configuration.
Size against the appliance's rated input; if it's close, look at a larger diameter or shorter length.
Picking a length
The right length depends on the distance between the gas outlet and the appliance stub-out, which varies from job to job. That's why BK builds this 3/4" kit in five lengths: 24", 36", 48", 60" and 72".
Measure from the gas outlet to the appliance inlet with the appliance in its working position. The installed hose should have no kinks, twists or excessive bends, and it should not touch the floor. Offsetting the two ends of the hose from each other, as BK recommends, keeps the appliance closer to the wall. A shorter hose carries more gas; a longer one gives the appliance more room to move for cleaning, within the limit set by the restraining cable.
| Length | Model | Price | Capacity (valve + quick disconnect) |
|---|---|---|---|
| 24" (this one) | BKG-GHC-7524-SCK9 | $396 | 208,000 BTU/hr |
| 36" | BKG-GHC-7536-SCK9 | $405 | 195,000 BTU/hr |
| 48" | BKG-GHC-7548-SCK9 | $440 | 184,000 BTU/hr |
| 60" | BKG-GHC-7560-SCK9 | $503 | 168,000 BTU/hr |
| 72" | BKG-GHC-7572-SCK9 | $541 | 168,000 BTU/hr |
At 24", this is the shortest length BK makes, so measure carefully before ordering. A hose that has to be pulled straight to reach is too short.
Same size, different kits
BK offers this 3/4" x 24" size several ways:
| BKG-GHC-7524 | Hose only: $207 ($189 less than this one) |
|---|---|
| BKG-GHC-7524-PT | Hose in display tube: $226 ($170 less than this one) |
| BKG-GHC-7524-QD-PT | Hose + quick disconnect (display tube): $318 ($78 less than this one) |
| BKG-GHC-7524-SCK2 | Kit #2: hose, quick disconnect, restraining cable: $339 ($57 less than this one) |
| BKG-GHC-7524-SCK3 | Kit #3: adds shut-off valve and two 90° elbows: $390 ($6 less than this one) |
| BKG-GHC-7524-SW3 | Swivel Pro kit: Kit #3 contents plus one Swivel Pro: $547 ($151 more than this one) |
| BKG-GHC-7524-2SW3 | Swivel Pro kit with two Swivel Pro connections: $704 ($308 more than this one) |
Before you install
What BK's manual requires, in short:
- Install and leak-test to the National Fuel Gas Code (ANSI Z223.1) and local codes. BK requires qualified personnel for installation and testing.
- Shut off the main gas line and the ball valve before connecting the hose or quick disconnect.
- An approved manual shut-off ball valve must sit at the connection from the gas line to the hose, within 6" of the appliance. This kit includes it.
- The gas outlet may not be hidden in or covered by drywall, flooring or partition walls.
- Use thread sealant or thread tape on NPT connections and tighten with wrenches.
- The restraining cable must be attached and stay connected whenever the appliance is in use. It's in this kit.
- Follow the gas-flow arrows on the quick disconnect. Maximum gas pressure through it is 1/2 psi (3.5 kPa), and it's not for dual-fed manifold lineups.
- Leak-test the final assembly with a leak-detection solution, never an open flame, and rinse with water afterward to prevent corrosion.
- Push the appliance back into position and check that the hose isn't over-bent or kinked.
Care: clean connections with mild products and rinse right away, keep the hose away from anything over 230°F (110°C), and never move an installed hose to another appliance. BK's full steps are summarized in our gas hose installation guide, and the BK PDFs are linked below.
What to check first
- Gas load. Add up the input ratings on the appliance data plate and compare with 208,000 BTU/hr, BK's rating for this size with shut-off valve and quick disconnect. At a 0.2" water column drop, BK's factor of 0.632 gives about 131,456 BTU/hr.
- Length. Measure the run with the appliance in place. The table above shows the other lengths and what each carries.
- Diameter. The 1/2" size suits smaller loads; 1" carries much more at the same length.
- Hardware. Valve, quick disconnect and restraining cable are all included.
- Gas supply layout. On a dual-fed manifold lineup, BK allows only the ball valve, not a quick disconnect.
- Installer. Plan for a qualified gas installer to connect and leak-test it.
BKG-GHC-7524-SCK9 questions
How much gas will the BKG-GHC-7524-SCK9 carry?
BK rates a 3/4" x 24" connector at 208,000 BTU/hr with shut-off valve and quick disconnect, at a 0.5" water column pressure drop with natural gas (0.64 specific gravity, 1,000 BTU per cubic foot). At 0.2" w.c. that's about 131,456 BTU/hr.
Does it work with propane?
BK's capacity figures are for natural gas. BK's quick connect is approved for 1st, 2nd and 3rd family gases under 50 mbar; for other conditions BK says to contact the manufacturer or gas supplier.
What's in the box?
The 24" x 3/4" hose plus the parts listed above, packaged in a point-of-purchase box.
Is the restraining cable required?
Yes. BK requires it to stay connected whenever the hose is installed, and its 5-year hose warranty requires a BK Resources restraining cable kit.
What's the warranty?
5 year warranty on hose, 1 year warranty on shut off valve, quick disconnect, 90° elbows, threaded nipples, & restraining cable. The warranty excludes shipping damage, misuse, and installations that don't follow BK's instructions or the applicable gas standards.
Can I move it to another appliance later?
No. BK calls for a new gas hose and installation hardware for each installation.
How do I clean behind the appliance?
Turn the gas and appliance knobs off, pull back the coupler to release the hose, keep the nipple off the floor, then unhook the cable. To reconnect, reattach the cable first, push the nipple in until it clips, turn the gas on at the ball valve and check for leaks.
Specifications
| Model | BKG-GHC-7524-SCK9 |
|---|---|
| Type | Connection Kit #9 |
| Inside diameter | 3/4" |
| Hose length | 24" |
| Hose | Heavy-duty T-304 corrugated stainless steel, stainless steel radial wrap |
| Coating | Protective translucent coating |
| Couplings | T-304 with zinc coating |
| Rated capacity | 208,000 BTU/hr with shut-off valve and quick disconnect |
| Capacity basis | ANSI Z21.69 test method; natural gas, 0.64 sp. gr., 1,000 BTU/cu ft, 0.5" w.c. pressure drop |
| Quick disconnect max pressure | 1/2 psi (3.5 kPa) |
| Packaging | Point-of-purchase box |
| Certification | cCSAus; Massachusetts approved |
| Meets ANSI | Z21.69a, Z21.69b, Z21.69-2002, Z21.41a-2005, Z21.41b-2010, Z21.41-2003 |
| Warranty | 5 year warranty on hose, 1 year warranty on shut off valve, quick disconnect, 90° elbows, threaded nipples, & restraining cable |