Skip to content

BK Resources BKG-GHC-5048-SP3 1/2" x 48" Set-Pro Gas Hose Connector Kit #3

Original price $456.00 - Original price $456.00
Original price
$456.00
$456.00 - $456.00
Current price $456.00

The BKG-GHC-5048-SP3 is BK Resources' Set-Pro Connection Kit #3 built around a 1/2" I.D. x 48" stainless steel gas hose with radial wrap and protective translucent coating.

What's in the box

  • Gas hose, 48" long x 1/2" I.D. stainless steel hose with radial wrap & protective translucent coating
  • (2) Set-Pro™
  • (1) shut off valve
  • (1) quick disconnect
  • (1) restraining cable & hardware
  • (2) male-to-female 90° elbows
  • (4) screws
  • (4) plastic anchors

Set-Pro is BK's professional equipment placement system for caster-mounted equipment: a set of two T-304 16 ga. stainless steel guides that give consistent equipment placement, reduce gas hose wear and tear, and help maintain NFPA 17A (5.6.4) and NFPA 96 (12.1.2.3). The Set-Pro pair is also sold separately as the BKG-CS ($155).

At a glance

  • Size: 1/2" inside diameter x 48" long
  • Rated capacity: 76,000 BTU/hr with shut-off valve and quick disconnect (BK chart, natural gas, 0.5" w.c. drop)
  • Kit includes: hose, shut-off valve, quick disconnect, restraining cable, two Set-Pro guides
  • Certification: cCSAus, Massachusetts approved
  • Hose warranty: 5 years; 1 year on the kit hardware
  • For: movable (caster-mounted) commercial gas appliances, per ANSI Z21.69 • CSA 6.16

Capacity with the kit installed

Installed with a shut-off valve and quick disconnect in line, BK's capacity chart rates a 1/2" x 48" hose at 76,000 BTU/hr (ANSI Z21.69 test method; natural gas, 0.64 specific gravity, 1,000 BTU per cubic foot, 0.5" water column pressure drop).

For comparison, the same length in 3/4" is rated 184,000 BTU/hr and 1" is rated 368,000 BTU/hr in this configuration.

Check that number against the input rating on the appliance's data plate.

Picking a length

BK makes this 1/2" kit in one length, 48". Because every gas line and stub-out is placed differently, BK says choosing the right length during installation is essential.

Measure from the gas outlet to the appliance inlet with the appliance in its working position. The installed hose should have no kinks, twists or excessive bends, and it should not touch the floor. Offsetting the two ends of the hose from each other, as BK recommends, keeps the appliance closer to the wall. A shorter hose carries more gas; a longer one gives the appliance more room to move for cleaning, within the limit set by the restraining cable.

Other 1/2" x 48" options

BK offers this 1/2" x 48" size several ways:

BKG-GHC-5048Hose only: $195 ($261 less than this one)
BKG-GHC-5048-PTHose in display tube: $216 ($240 less than this one)
BKG-GHC-5048-QD-PTHose + quick disconnect (display tube): $255 ($201 less than this one)
BKG-GHC-5048-SCK2Kit #2: hose, quick disconnect, restraining cable: $280 ($176 less than this one)
BKG-GHC-5048-SCK3Kit #3: adds shut-off valve and two 90° elbows: $315 ($141 less than this one)
BKG-GHC-5048-SCK9Kit #9: valve, quick disconnect, cable, two 90° female elbows, two nipples: $324 ($132 less than this one)
BKG-GHC-5048-SW3Swivel Pro kit: Kit #3 contents plus one Swivel Pro: $466 ($10 more than this one)
BKG-GHC-5048-2SW3Swivel Pro kit with two Swivel Pro connections: $615 ($159 more than this one)
BKG-GHC-5048-SWSP3Set-Pro kit with Swivel Pro: $605 ($149 more than this one)

Before you install

BK's installation manual sets out these requirements for its gas connectors:

  • Install and leak-test to the National Fuel Gas Code (ANSI Z223.1) and local codes. BK requires qualified personnel for installation and testing.
  • Shut off the main gas line and the ball valve before connecting the hose or quick disconnect.
  • An approved manual shut-off ball valve must sit at the connection from the gas line to the hose, within 6" of the appliance. This kit includes it.
  • The gas outlet may not be hidden in or covered by drywall, flooring or partition walls.
  • Use thread sealant or thread tape on NPT connections and tighten with wrenches.
  • The restraining cable must be attached and stay connected whenever the appliance is in use. It's in this kit.
  • Follow the gas-flow arrows on the quick disconnect. Maximum gas pressure through it is 1/2 psi (3.5 kPa), and it's not for dual-fed manifold lineups.
  • Leak-test the final assembly with a leak-detection solution, never an open flame, and rinse with water afterward to prevent corrosion.
  • Push the appliance back into position and check that the hose isn't over-bent or kinked.

Care: clean connections with mild products and rinse right away, keep the hose away from anything over 230°F (110°C), and never move an installed hose to another appliance. BK's full steps are summarized in our gas hose installation guide, and the BK PDFs are linked below.

Before you order

  1. Gas load. Add up the input ratings on the appliance data plate and compare with 76,000 BTU/hr, BK's rating for this size with shut-off valve and quick disconnect. At a 0.2" water column drop, BK's factor of 0.632 gives about 48,032 BTU/hr.
  2. Length. Measure the run with the appliance in place. BK makes this kit only in 48".
  3. Diameter. If the load is close to the limit, the 3/4" size carries considerably more at the same length.
  4. Hardware. Valve, quick disconnect and restraining cable are all included.
  5. Gas supply layout. On a dual-fed manifold lineup, BK allows only the ball valve, not a quick disconnect.
  6. Installer. Plan for a qualified gas installer to connect and leak-test it.

BKG-GHC-5048-SP3 questions

How much gas will the BKG-GHC-5048-SP3 carry?
BK rates a 1/2" x 48" connector at 76,000 BTU/hr with shut-off valve and quick disconnect, at a 0.5" water column pressure drop with natural gas (0.64 specific gravity, 1,000 BTU per cubic foot). At 0.2" w.c. that's about 48,032 BTU/hr.

Does it work with propane?
BK's capacity figures are for natural gas. BK's quick connect is approved for 1st, 2nd and 3rd family gases under 50 mbar; for other conditions BK says to contact the manufacturer or gas supplier.

What's in the box?
The 48" x 1/2" hose plus the parts listed above, packaged in a point-of-purchase box.

Is the restraining cable required?
Yes. BK requires it to stay connected whenever the hose is installed, and its 5-year hose warranty requires a BK Resources restraining cable kit.

What's the warranty?
5 year warranty on hose, 1 year warranty on shut off valve, quick disconnect, 90° elbows, & restraining cable. The warranty excludes shipping damage, misuse, and installations that don't follow BK's instructions or the applicable gas standards.

Can I move it to another appliance later?
No. BK calls for a new gas hose and installation hardware for each installation.

How do I clean behind the appliance?
Turn the gas and appliance knobs off, pull back the coupler to release the hose, keep the nipple off the floor, then unhook the cable. To reconnect, reattach the cable first, push the nipple in until it clips, turn the gas on at the ball valve and check for leaks.

Specifications

ModelBKG-GHC-5048-SP3
TypeSet-Pro Connection Kit #3
Inside diameter1/2"
Hose length48"
HoseHeavy-duty T-304 corrugated stainless steel, stainless steel radial wrap
CoatingProtective translucent coating
CouplingsT-304 with zinc coating
Rated capacity76,000 BTU/hr with shut-off valve and quick disconnect
Capacity basisANSI Z21.69 test method; natural gas, 0.64 sp. gr., 1,000 BTU/cu ft, 0.5" w.c. pressure drop
Quick disconnect max pressure1/2 psi (3.5 kPa)
PackagingPoint-of-purchase display box
CertificationcCSAus; Massachusetts approved
Meets ANSIZ21.69a, Z21.69b, Z21.69-2002, Z21.41a-2005, Z21.41b-2010, Z21.41-2003
Warranty5 year warranty on hose, 1 year warranty on shut off valve, quick disconnect, 90° elbows, & restraining cable

Documents and downloads

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare